JUTA

JUTA 300TT

JUTA geoNETEX A PP is a range of non-woven geotextile and is suitable for a variety of civil engineering projects. It is manufactured from high tenacity virgin polypropylene staple fibres, which have a high resistance to acids, alkalis and most solvents.

Read More

Product Benefits

Functionality includes:-

  • Separation
  • Hydraulic & Filtration
  • Protection
  • Third-Party BBA Certification
  • CE Marked
Product Description

JUTA geoNETEX A PP is a range of non-woven geotextile manufactured from UV stabilised, high tenacity, virgin polypropylene fibres that have been mechanically entangled to provide high strength, high extensibility, high loft and excellent abrasion characteristics. Functionality includes:- Separation, filtration & protection.

JUTA 300TT

This product is associated with the following NBS Create Clause:

 

45-65-50/325 Plastic Sheets

 

This product is associated with the following NBS Clauses:

 

 

D20 Excavating and filling

D41 Crib walls, gabions and other gravity retaining walls

J44 Sheet linings for pools/lakes/waterways

Q20 Granular sub-bases to roads/ pavings

Q22 Asphalt roads/ pavings

 

 

Q23 Gravel/ hoggin/ woodchip roads/ pavings

Q24 Interlocking brick/ block roads/ pavings

Q25 Slab/ brick/ sett/ cobble pavings

Q31 External planting

Q37 Green roofs

R12 Below ground drainage systems

R16 Groundwater pressure relief drainage

R17 Soakaway, septic tank and sewage treatment units

  • Separation
  • Protection
  • SUDS
  • Filtration
  • Erosion Control
  • Horitcultural
  • Reinforcement

 

JUTA 300TT
Site Investigation
Site Investigation
Site Investigation Reports Monitoring Results. We review these reports and advise routes for compliance.
System Design
System Design
Full Ground Gas Protection System Design available.
Specification
Specification
Wide library of standard details with site specific details on request.
Installation
Installation
All our installers are certified NVQ Level 2 qualified installation contractors.
Validation
Validation
We ensure your project complies with the relevant building regulations.

Ground Gas Standards 

There are many different standards and guidance documents that detail how to understand the risk of ground contamination, and design solutions to mitigate these risks. The different documents relate to different ground contamination. Below are some of the key documents to be aware of and refer to:

BS 8485:2015+A1:2019 – Codes of practice for the design of protective measures for methane and carbon dioxide ground gases for new buildings.

  • Ground gases typically found near landfill sites, but can occur from other sources
  • Encourages the use of qualified installers
  • Validation to Ciria C735 is a requirement
  • Additional influences on the system should be considered, such as the hydrostatic conditions, and the likelihood of the source contaminant being in direct contact with the protective measures proposed
JUTA 300TT

BRE 211:2015 – Guidance on protective measures for new buildings. (RADON)

  • Naturally occurring ground gas. Larger concentrations in the South-West of UK
  • Minimum recommendation is a membrane of 300 micrometre (1200 gauge) polyethylene sheet or equivalent
  • It must be installed with considerable care and protected once installed
  • Taped laps are required
JUTA 300TT

CIRIA C748:2014 – Guidance on the use of plastic membranes as VOC vapour barriers

CIRIA C682:2009 – VOC Handbook

Risk based approach
No quantifiable limits on material performance
Testing to ISO 15105-2 and EN 14414/EN 14415
9 main VOC types are tested for
Welded laps are required as most tapes are made from bitumen/butyl and are affected by VOCs

JUTA 300TT

CIRIA C735:2014 – Good practice on testing and verification of protection systems to buildings from hazardous gases

  • Good practice on testing and verification of protection systems to buildings from hazardous gases
  • Check design and detailing is in accordance with site requirements
  • Checks the competency of the installer (NVQ LEVEL 2 minimum)
  • Test integrity of the membrane/barrier system
  • Visual inspection
  • Written report on inspection/testing and sign-off

BS8102:2009 – Code of practice for protection of below ground structures against water from the ground

JUTA 300TT

JUTA Solutions & Applications

Our gas protection membranes suit a variety of applications and situations, with our TITAN® range offering not only gas protection but also having superior waterproofing and invasive weed control qualities.

BRE 211 NHBC (Amber 1) BS8485:2015 + A1 2019 / NHBC (Amber 2) C748 C748 BS8102:2009 RPS178 C753 BBA Agreement Certificate
Radon Bulk Ground Gasses Cardbon Dioxide and Methane VOC Vapour Permeation Hydrocarbons Immersions TYPE-A Bonded Waterproofing Invasive Weed Control SuDs Impermeable Membrane
GP®1
GP®2
GP®4
GP®5
GP®H
GP®L
GP® TITANFLEX
GP® TITANBOND
GP® TITANTANK
GP® LIQUID BARRIER
GP®H 0.6mm

Get In Touch With The Experts

If you feel first class service, premium products direct from source, and bespoke solutions are right for you then don't hesitate to contact our team today on 01772 754177 or email us at info@juta.co.uk

Contact Us