Home // Civil & Containment Engineering // GeoMembranes // HDPE 0.6 MM

HDPE 0.6 MM

JUNIFOL 0.6 MM HDPE High-Density Polyethylene Geomembrane is designed to protect structures from the ingress of moisture, water, liquids, radon, carbon dioxide and methane together with chemicals.

Suitable for use in various demanding geomembrane applications such as SUDS, root barrier, waterproofing and radon protection and permeable paving.

Designed to perform as a robust waterproofing barrier protection system.
Provides resistance to root penetration from invasive species, including (but not limited to): Japanese Knotweed, Bamboo, Mustard seed, Meadow grass, Ivy, Hybrid poplars, Willow, Elm, Maple, Mare’s tail, ground creeping plants, edible plants and aquatic plants.
Fully weldable, category 2 attenuation grade liner fully conformant to C753 and BS533-13 and is CE marked for use in EN13967 (A/T) application areas.

Make an Enquiry Standard Details

HDPE 0.6 MM TDS

Download

Product Description

HDPE 0.6 mm – is a mono layer, high-density polyethylene membrane specifically designed and manufactured to perform as a robust waterproofing barrier protection system, which is suitable for use in various demanding geomembrane applications such as SUDS, root barrier, waterproofing and radon protection and permeable paving.

HDPE 0.6 mm is a fully weldable, category 2 attenuation grade liner fully conformant to C753 and BS7533-13 and is CE marked for use in the following application areas: EN13967 (A/T).

HDPE 0.6 mm provides resistance to root penetration from invasive species, including (but not limited to): Japanese Knotweed, Bamboo, Mustard Seed, meadow Grass, Ivy, Hybrid poplars, Willow, Elm, Maple, Mare’s Tail, ground creeping plants, edible plants and aquatic plants.

Specifications

General Information

Color	Black
Material	Polyethylene
	High-density polyethylene (HDPE).
	Mono-layer, linear high-density polyethylene membrane.
Size	2.5 x 50 m x 0.6 mm
Uniclass 2015	Pr_25_57_65_60 Plastics sheets
CAWS	J44/115 Geomembrane lining
	J44/110 Geomembrane lining
	J40/145 Loose laid weldable polyethylene gas retardant damp proofing
	J40/140 Loose laid plastics or rubber sheet gas retardant damp proofing
	J40/35 Loose laid plastics or rubber gas retardant damp proofing
	D20/550 Geotextile sheet
	D20/58 Geotextile sheet
Product range	Junifol Geomembrane

Specification data - Plastics sheets

Material	High-density polyethylene (HDPE).
Purpose	Waterproof layer.
Standard	To EN 14150, EN 1931, EN 1928, EN 12730-B, EN 12311-2(A), EN 12310-1, EN 12691 (A), EN 12317-2, EN 1269, EN 1847.
Performance characteristics
Tensile strength (minimum)	500 N/50mm.
Tear resistance	MD:450 N; CD: 500 N.
Resistant to underground gases	Radon.
Physical properties
Thickness (minimum)	0.6 mm.
Width (minimum)	2.5 m / 5.1m
Roll length (minimum)	50 m. / 100 m.
Environmental Information
Country of material origin	United Kingdom

Physical Properties

Characteristics	Test Method	HDPE 0.6 MM
Thickness	EN 1849-2	0.6 mm
Width	EN 1849-2	2.5 or 5.1 m
Length	EN 1849-2	50 or 100 m
Density	Length	0.939 g/cm³
Resistance to Roots	Length	Impenetrable

Hydraulic Press

Characteristics	Test Method	HDPE 0.6 MM
Permeability to liquids	EN 14510	1.0 x 10^-6 m³/(m².d)
Water Tightness (60 kPa)	EN 1928	Pass

Mechanical Properties

Characteristics	Test Method	HDPE 0.6 MM
Resistance to Static Load	EN 12730-B	> 20 kg
Tensile Strength (MD)	EN 12311-2 (A)	500 N/50mm
Tensile Strength (CMD)	EN 12311-2 (A)	500 N/50mm
Tear Strength (MD)	EN 12310-1	450 N
Tear Strength (CMD)	EN 12310-1	500 N
Resistance to Impact	EN 12691 (A)	> 2000 mm
Shear Resistance of Joint	EN 12317-2	Welded: 400 N/50mm GP® TITAN TAPE: 400 N/50mm

Durability and Chemical Resistance

Characteristics	Test Method	HDPE 0.6 MM
Resistance to Elevated Temperature	EN 1296	Conforming
Resistance to Liquid Chemicals	EN 1847	Conforming

Gas Permeability

Characteristics	Test Method	HDPE 0.6 MM
Radon Permeability	K124/02/95	2.0 x 10^-12 m²/s

View Data Sheet

Applications

HDPE 0.6 mm is a robust weldable geomembrane suitable for attenuation tank encapsulations, porous sub-base installations, containment and cut-off trenches, structural waterproofing. HDPE 0.6 mm is a chemically inert membrane offering designers and specifiers a range of critical properties that meet the needs of today’s demanding geomembrane applications including high water table sites. HDPE 0.6 mm can be fully welded where required.

Installation

HDPE 0.6 mm should be installed on a blinded or smooth surface, free from sharp protrusions (typically maximum permissible particle size in direct contact with the membrane should be < 10mm). Avoid areas of unsupported membrane. Where required, adequate protection should be applied over the membrane to prevent damage after installation. HDPE 0.6 mm exhibits superior welding properties, making it ideal for on-site welding joints.

Standard Details

A selection of standard details for information and education purposes only. Note - it is strongly advised appropriately qualified, and insured personnel undertake gas membrane installs. A gas membrane performs a critical function in the application setting and has an anticipated design service life in excess of 60 years. Do not attempt to install gas membranes from these details alone. Sole rights for use and distribution are owned by JUTA UK LTD.

HDPE 0.6 MM
Installation Guidance

Download

Handling & Storage

Store in a clean and dry environment, with tolls stacked no more than 5 units high. HDPE 0.6 mm is classified as non-hazardous. It is chemically inert and is not affected by acids and alkalis that may be present in the subsoils. The material is not recommended for uses where it will be exposed to long periods of outdoor weathering, such as exposure to Ultraviolet light that will embrittle the product. Care should be take to avoid accidental damage when handling the membrane on site.

Compliance & Certifications

CE Mark - EN13967:2012 (A/T)

BS7533-13 and ‘Code for Sustainable Homes 2006’ Conformant

Conforms to CIRIA C697 and C753 as an Attenuation Membrane

Site Investigation

Site Investigation Reports Monitoring Results. We review these reports and advise routes for compliance.

System Design

Full Ground Gas Protection System Design available.

Specification

Wide library of standard details with site specific details on request.

Installation

All our installers are certified NVQ Level 2 qualified installation contractors.

Validation

We ensure your project complies with the relevant building regulations.

Ground Gas Standards

There are many different standards and guidance documents that detail how to understand the risk of ground contamination, and design solutions to mitigate these risks. The different documents relate to different ground contamination. Below are some of the key documents to be aware of and refer to:

Methane (CH4) and Carbon Dioxide (CO2)

BS 8485:2015+A1:2019 – Codes of practice for the design of protective measures for methane and carbon dioxide ground gases for new buildings.

Ground gases typically found near landfill sites, but can occur from other sources
Encourages the use of qualified installers
Validation to Ciria C735 is a requirement
Additional influences on the system should be considered, such as the hydrostatic conditions, and the likelihood of the source contaminant being in direct contact with the protective measures proposed

Radon (Rn)

BRE 211:2015 – Guidance on protective measures for new buildings. (RADON)

Naturally occurring ground gas. Larger concentrations in the South-West of UK
Minimum recommendation is a membrane of 300 micrometre (1200 gauge) polyethylene sheet or equivalent
It must be installed with considerable care and protected once installed
Taped laps are required

VOCs & Hydrocarbons

CIRIA C748:2014 – Guidance on the use of plastic membranes as VOC vapour barriers

CIRIA C682:2009 – VOC Handbook

Risk-based approach
No quantifiable limits on material performance
Testing to ISO 15105-2 and EN 14414/EN 14415
9 main VOC types are tested for
Welded laps are required as most tapes are made from bitumen/butyl and are affected by VOCs

General

CIRIA C735:2014 – Good practice on testing and verification of protection systems to buildings from hazardous gases

Good practice on testing and verification of protection systems to buildings from hazardous gases
Check design and detailing is in accordance with site requirements
Checks the competency of the installer (NVQ LEVEL 2 minimum)
Test integrity of the membrane/barrier system
Visual inspection
Written report on inspection/testing and sign-off
BS8102:2009 – Code of practice for protection of below ground structures against water from the ground

JUTA Solutions & Applications

Our gas protection membranes suit a variety of applications and situations, with our TITAN^® range offering not only gas protection but also having superior waterproofing and invasive weed control qualities.

	BRE 211	NHBC (Amber 1)	BS8485:2015 + A1 2019 / NHBC (Amber 2)	C748	C748	BS8102:2009	RPS178	C753	BBA Agreement Certificate
	Radon	Bulk Ground Gasses	Cardbon Dioxide and Methane	VOC Vapour Permeation	Hydrocarbons Immersions	TYPE-A Bonded Waterproofing	Invasive Weed Control	SuDs Impermeable Membrane	BBA Agreement Certificate
GP^®1
GP^®2
GP^®4
GP^®5
GP^®H
GP^®L
GP^® TITANFLEX
GP^® TITANBOND
GP^® TITANTANK
GP^® LIQUID BARRIER
GP^®H 0.6mm

Get In Touch With The Experts

If you feel first class service, premium products direct from source, and bespoke solutions are right for you then don't hesitate to contact our team today on 01772 754177 or email us at info@juta.co.uk

HDPE 0.6 MM

Product Benefits

Manhole Sealing

Pond Liner

Swale Liner

Permeable

Attenuation Tank

Concrete Tank Pit

Additional

CE Mark - EN13967:2012 (A/T)

BS7533-13 and ‘Code for Sustainable Homes 2006’ Conformant

Conforms to CIRIA C697 and C753 as an Attenuation Membrane

Ground Gas Standards

JUTA Solutions & Applications

You may also be interested in...

Get In Touch With The Experts

Gas Protection

Waterproofing

Civil & Containment Engineering

Tiltex

Agriculture

Grass

Roofing

SUDS